BMW spare parts: BMW body parts: BMW e30 parts: Repair BMW: Check of pressure of fuel

Pressure check fuel, GENERAL DATA


CARBURETTOR ENGINES

For check of pressure of fuel it is necessary to include a manometre between the fuel pump and a tube of giving of fuel in bmw auto parts the carburettor. It is necessary also to shunt the return fuel valve included in a highway after the fuel pump. The PERFORMANCE ORDER
In the absence of a manometre pressure can be checked up on струе from the hose disconnected from the pump, turning the engine a starter (disconnect also a high-voltage wire from the ignition coil).



INJECTOR ENGINES
The prevention

The fuel filter should be in a satisfactory condition. If the filter is littered, it is necessary to replace it.
On cars with the pump of pumping pressure is measured at work of the basic pump and the pumping pump.

Check of work of the basic fuel pump and the pump sops PERFORMANCEORDER

1. In system of injection L-Jetronic перемкните conclusions 30 and 87b on a socket of the relay of the fuel pump.

2. In system Motronic conclusions 30 and 87.

3. On models after 1987 for access to the relay and the management block turn away 4 bolts and remove a cover.

4. Then conclusions 30 and 87 on a relay socket.

At inclusion of ignition from a tank the sound of the working pump should be listened. The given procedure concerns and the pumping pump.

Check of pressure of fuel the PERFORMANCE ORDER
1. Execute decompressions and disconnect the battery from weight.


2. In system of injection L-Jetronic and early systems Motronic disconnect a highway of giving of fuel on the fuel distributor. On late systems Motronic oem bmw parts disconnect a highway on the fuel filter.

3. In highway rupture include a manometer.
4. Connect the battery to weight, перемкните conclusions to the pump relay, include ignition and consider pressure.
5. If pressure below norm check up presence of leaks in system, replace the filter and repeat measurements, check up the pressure developed by the pump and a condition of a regulator of pressure.
6. If pressure above norm check up a condition of a return gasoline pipe line. If the gasoline pipe line is not littered, replace a pressure regulator.
7. Check up pressure later 5 minutes after varis bmw parts ignition reenergizing. If pressure below norm check up presence of leaks in system, check up wirings diagrams the pressure developed by the pump, a condition of a regulator of pressure and atomizers.



Check of pressure of the fuel developed by the pump
The prevention

For measurements the manometre joins directly the pump and standard procedure decompressions parts for bmw after tests is inapplicable. Therefore, the manometre with the pitting valve is required. The PERFORMANCE ORDER
1. Execute and disconnect the battery from weight.
2. Disconnect a highway of giving of fuel on the distributor of fuel and attach to a highway a manometre.
3. Connect the battery to weight, conclusions to the pump relay, include ignition and consider pressure.
4. If pressure below norm check up presence of leaks in system. If the system is tight, replace the pump.
5. Check up pressure later 5 minutes after ignition reenergizing. If pressure below norm check up presence of leaks in system. If the system is tight, replace the pump.
6. Remove a crosspiece and dump pressure, having directed a fuel stream in a vessel.



Check of the pump of pumping of fuel the PERFORMANCE ORDER
1. Execute декомпрессию and disconnect the battery from weight.
2. Remove hatch the pumping pump (is under a back seat or under a rug in a luggage carrier, depending on model). Attach a manometre to the final union of the pump.
3. Connect the battery to weight, bmw body parts conclusions to the pump relay, include ignition and consider pressure. If pressure below norm replace the pumping pump.


Check of the relay of the fuel pump
The scheme of the device of the relay of the fuel wirings diagramspump and designation of conclusions (the 4-cylinder engine)

1. A signal from a starter
2. A rotation signal сranked shaft
3. Pressure of the battery
4. To the fuel pump (+) 5. The control of level of fuel
6. Weight
7. Pressure of the battery at ignition inclusion


The scheme of the device of the relay of the fuel pump and designation of conclusions (the 6-cylinder engine)

1. Pressure of the battery
2. Pressure (+) from the main relay
3. Weight from the block of management Motronic
4. To the fuel pump (+)


The relay of the fuel pump on the 4-cylinder engine () and on the 6-cylinder engine ()



PERFORMANCE ORDER
1. Include ignition and check up presence of pressure Wirings diagramsof the Repair BMW battery on conclusions 30 (engine M10) or 15 (М20 and М40) from an underside of a socket of the relay.
The prevention


If in cars with the battery in which it is mounted in a pressure luggage carrier on these conclusions is not present, check up a condition bmw replacement parts of a fusible crosspiece (on a current 50 And, located in 15 sm from the battery).
2. Switch off ignition, disconnect the relay from a BMW e30 parts socket, connect the voltmeter between conclusions 85 (-) and 86 (+) (engine M20) or between a conclusion 50 and weight (М10 and М40) and check up presence of pressure of the battery between these conclusions at starter inclusion.
3. In the absence of pressure check up safety locks BMW body parts and a chain. If pressure is, but the pump works only with a crosspiece the relay replace.
4. If the pump does not work and after relay replacement check up pressure on pump conclusions. If necessary replace the pump.

BMW spare parts: BMW body parts: BMW e30 parts: Repair BMW: The fuel pump, the pump of pumping and the gauge of level of fuel in a tank.

The fuel pump of early system of injection Motronic:

1. A clamping washer

2. The gauge of level of fuel

3. A lining

4, 11. A hose

5. The holder

6. The pump

7. The filter

8. Shoetree

9. The control valve

10. A suppressor of pulsations


The fuel pump (the carburetor engine) the PERFORMANCE ORDER
1. Disconnect the battery from weight, disconnect from the pump hoses, turn away 2 nuts of fastening of the pump.
2. Remove the pump, if necessary displace the pump easy blow on wooden бруску.
3. Remove 2 linings.
4. The pump not folding and to oem bmw parts repair is not subject. Installation parts for bmw is carried out upside-down. Replace linings from both parties of the prorate of the pump, not breaking their thickness.



The fuel pump (injector engine)
The prevention
In system of injection L-Jetronic the pumping pump bmw auto parts is mounted near to a tank, in system Motronic this pump is mounted in a fuel tank. The gauge of level of fuel is mounted in a fuel tank on the pump of pumping or on varis bmw parts the fuel pump. The PERFORMANCE ORDER
Execute decompression and disconnect the battery from weight.


The fuel pump mounted out of бака PERFORMANCE ORDER

1. Lift the car.
2. Remove a cover and disconnect from the wire pump.
3. Press clips fuel hoses of the pump and disconnect them on the pump.
4. Turn away screws of fastening and remove the pump. Installation parts for bmw is carried out upside-down.



The fuel pump mounted in a tank (or the pumping pump) the PERFORMANCE ORDER


1. Turn away screws and remove лючок (is under a back seat or under a rug in a luggage carrier, depending on model).

2. Disconnect sockets of the pump of pumping (1) and the gauge of level of fuel (2) in early system of injection Motronic.

3. For a socket detachment hook скобу so that dredging was combined with a groove on a latch and dissolve socket parts

4. On a part of cars to take the pump with the gauge it is necessary to turn this knot counter-clockwise.

5. On a part of cars the knot of the pump with the gauge fastens these nuts.

6. In early system of injection Motronic at first get the bmw body parts gauge of level of fuel, then get the pump, not disconnecting hoses.

7. On early models turn away fastening screws, take away bmw replacement parts and remove the pumping pump.
8. Installation is carried out upside-down. If necessary replace a lining between the pump and a fuel tank.


The gauge of level of fuel

Conclusions of the gauge of level of fuel in late system Motronic 1. Weight of the gauge

2. To a control lamp

3. The gauge

4. Weight of the pump

5. The pump


PERFORMANCE ORDER
1. Remove the pump with the gauge.
2. In system of injection L-Jetronic and in early system Motronic check up resistance between the specified conclusions according to the table. Of late system Motronic be bmw body parts convinced, that resistance between conclusions 1 and 3 decreases at a raising плунжера the gauge.
3. If resistance differs, the gauge replace.
4. Installation is carried out upside-down.

BMW spare parts: Fix-A-Dent Auto Body: Cold forging, dispersal, editing, straightening

At forging preparation in an external part of a bend is extended, and with internal — is compressed and flattened. On behr bmw parts and flattening all methods applied to formation of metal without removal of a shaving are based. Many metals in a cold condition soft and ковкие, for example gold, silver, copper, a brass, tin and aluminium. These metals behr bmw parts at processing by a hammer can be flattened out to (be extended), not losing the durability.

At forging the cross-section section of preparation decreases, and at a deposit — increases. During time протяжки and deposits owing to numerous blows Fix-A-Dent Auto Body of a hammer metal becomes fragile, and there is a danger of rupture of metal. Therefore from time to time metal warm up and pickle.

Formation soft

Metal considerably will improve as a result of heating. Such hot ковка is a forge work during which time to the heated piece of iron on an anvil powerful blows of a hammer form. Details about dispersal and cold forging are resulted in following subsection.

Hammer and linings (substrate)

Influence of blow of a hammer on metal depends on quality of a substrate and hardness of a hammer

Firm substrate — a firm hammer. If the hammer is firmer than preparation at blow metal disperses in the parties, its cross-section is flattened out, extended also
in a blow place decreases. For example, the metal sheet lays on a firm surface of an anvil and it process a metalwork hammer, боек which also is executed from the tempered steel.

Soft substrate — a firm hammer. If the substrate is softer than a hammer and preparation at blow by a hammer metal is flattened out not in the parties, and in a direction of a soft substrate. It is especially convenient at repair of metal products with Fix-A-Dent Auto Body dents. Thus air under a dent is especially soft lining. At blow by a hammer on a dent — for thin (automobile) steel sheets the hammer from an artificial material varis bmw parts suffices — metal is flattened out in a direction of a soft lining, i.e. Air. In such a way level metal sheets.

By the same principle make разгонку. When a hammer with firm brisk (metalwork, разгонным a hammer) strike on equal sheet of metal on a blow place varis bmw parts there is a deepening if a lining on which preparation lays, soft (for example, the lead plate or wooden брусок). Under the further blows of a hammer the metal sheet in a blow place is extended.

Firm substrate — a soft hammer. If the substrate is firmer than preparation, and the hammer is softer than preparation blows of a hammer it can be flattened parts foe bmw out and extended. Energy of blow partially comes back in a soft hammer.

Such way apply to straightening of the bent metal sheets. While air is under a dent, the metal sheet is exposed разгонке and is parts foe bmw straightened, and after straightening blows cannot deform preparation any more.

Рихтовка and straightening Рихтовка is an elimination of the undesirable deformations which have arisen, for example, at transportation, inept Fix-A-Dent Auto Body storage or at excessive loadings. Such deformations are inevitable at some kinds of metal working,
For example a curvature of metal sheets during welding or at cutting. Рихтовку make mechanically by means of a hammer or by means of clamps and a vice for отгибки, and also thermal way — a flame torches.

The bent metal sheets. Thin sheets of metal are corrected by means of a wooden, rubber or synthetic hammer. Begin with blows on bmw suspension parts the centre, and then move on a diagonal to an angular zone, as is shown in 51. Blows should be uniform and not strained. It is necessary to avoid double blows in the same place.

Metal plates with dents. Such plates stack a dent up on a smooth firm lining and a hammer strike on a dent. To this purpose apply a wooden, rubber or synthetic hammer, as it should be softer some straightened metal to avoid new deformations. Thanks to bmw salvage parts hammer blows occurs разгонка metal and the dent disappears. When the plate contacts lined, blows should be stopped, differently on this place there will be a metal stretching.

On the same method eliminate deformations in convex sheets of metal. More often this method apply to straightening of the damaged bmw replacement parts automobile bodies. As linings use various бойки (support), i.e. Steel Fix-A-Dent Auto Body tools with a firm and convex surface. Them keep one hand under metal sheet, and other hand strike on sheet a hammer.

Other method of straightening consists in that by means of a hammer to strike on metal on a spiral round camber, using thus a bmw replacement parts combination «a firm substrate — a firm hammer» (see above). The further from camber make blows, the they should be stronger. At use of the given method in no event it is impossible to beat a hammer on camber.

Very big cambers in metal sheets are good for eliminating by means of a flame сварочной torches. A zone round camber top warm up also metal here it is extended, that leads усадке metal in a place. The part of preparation which bmw auto parts was extended owing to heating, after cooling starts to be compressed. Thus under the influence of a flame deformation сначале amplifies, but after cooling disappears. For confident use of this method it is necessary to save up some experience.

Рихтовка sheet iron. The bent products the convex party stack on a firm substrate and straighten by means of a hammer. On small products the parts for bmw cars deformed place straighten by means of a vice.

The braided cores clamp in a vice, seize suitable pincers or, for example, bmw replacement parts and straighten preparation. Heating up a bend place, it is possible to facilitate considerably.

BMW spare parts: Fix-A-Dent Auto Body: That it is necessary to know about anticorrosive processing of a body

As is known, any car starts to rust in due course is the fact. Imperfect "know-how", and also anti ice means for roads – salt and sand promote it. To stop corrosion completely it is impossible, and here to reduce it to a minimum – quite. For this purpose parts foe bmw also anticorrosive processing is applied. Corrosion happens three kinds: chemical, electrochemical, and. The Most widespread kind of corrosion bmw suspension parts of the car – electrochemical. Roads which bmw salvage parts during winter time constantly salt, a rain, snow, a condensate varis bmw parts at change of a temperature mode of air – all contains water, in which large quantity
Various substances. The latent cavities of a body – thresholds, to a varis bmw parts cavity of doors where water accumulates, a dirt and salt are most subject to corrosion. To remove drying it it is practically impossible.

At anticorrosive processing of the car it is not necessary to stop on a bmw replacement parts of works, to do all at once is better. Full anticorrosive parts foe bmw processing consists of several kinds of works. Each kind protects a Fix-A-Dent Auto Body certain problem site of the car. Recently for body protection application is extended enough
Special mastics of a dense bmw auto parts consistence which, drying up, remains elastic. The covering from mastic protects a body from abrasive deterioration, preventing corrosion. Mastic put manually, a brush, or spray by means of the equipment.



The difficult moment is behr bmw parts processing of the latent cavities which make by means of dispersion of the protective substance easily getting into inaccessible places. Besides, for corrosion decrease, it is possible to use additional components, for parts for bmw cars example, mudguards or. Thus places of fastenings are necessary for processing
Special structure. It is not necessary to do anticorrosive processing independently so the wrong choice of protection frames or a banal carelessness is possible at work.

Is better to address in the anticorrosive centre with good reputation.

BMW spare parts: Restoration of the form of a body by editing and a Fix-A-Dent Auto Body

The technology of elimination of deformations of a body depends on a kind of a warp and character of deformations of details. Dents in body and plumage panels at which metal after blow will not stretch, level expression or to pull a concave site before giving to it of correct curvature and in need of the subsequent рихтовкой the squeezed out surface more often.
Formed in the panel at the big stretching of metal сamber it is impossible to correct рихтовкой as in the course of its performance the top сamber varis bmw parts can lose stability and move on other party of sheet. This circumstance if to consider, that for elimination сamber it is necessary to besiege surplus of metal, defines a way of its editing.
Elimination of deformations in Body details parts foe bmw. For correction of dents and restoration of the form of surfaces of elements of a body use the manual tool presented to section
The big nomenclature Fix-A-Dent Auto Body hammers assumes application of this or that hammer depending on character of a dent and the surface form. A number of hammers has polished Fix-A-Dent Auto Body a part that allows to reach high cleanliness of editing, and on occasion to make elimination of damages without destruction of a paint and varnish covering.

Anvils and shaped plates serve for support of sheet during correction of a dent by a hammer. The form and the sizes of plates and anvils are executed with the account of most often meeting curvature of details of a body and give the chance to apply them at restoration of various sites of a body.

Levers are intended for correction of various dents. The design of levers and length of some from them provides their application in varis bmw parts remote places through technological windows and apertures in body details.

Form restoration кузовных details with use Fix-A-Dent Auto Body the tool. Editing сamber carry out in cold or нагретом a condition. Elimination сamber > in a cold condition is based on a metal stretching on concentric circles or on radiuses from сamber to the intact part of metal (fig. 6.1). At editing smooth transition behr bmw parts from the highest part parts foe bmw сamber to a surface of the panel surrounding it is formed. For this purpose in a direction from the metal surrounding сamber, to the curved part of a surface put a hammer a consecutive series of blows on a circle. In process of hammer approach to border сamber force of blow reduce. The more there will be a behr bmw parts number of circles on the panel at Fix-A-Dent Auto Body, the transition from сamber to the intact part of metal more smoothly will turn out.

Fig. 6.1. Elimination сamber in panels of a body without heating:
And - sites of the panel with сamber; - the scheme of a direction of blows by a hammer (are specified by arrows); / - сamber: 2 - the panel; 3 - the sites of the panel which are subject to extension рихтовкой by means of a hammer: 4 - curvature of the panel after editing сamber

Editing of the deformed surfaces on a rectilinear site of obverse panels with use of a basic plate and hammer is shown on fig. 6.2, and. Correction of deformations on details with not round surfaces carry out with use киянки and shaped plates or anvils of a special profile (fig. 6.2,). On fig. 6.2, in process parts foe bmw insignificant dents on obverse panels of a body, such as a roof is shown, to a door, a cowl, a luggage carrier cover, wings, etc. Sequence of correction of dents on the details of the body having the rounded off obverse surface, is presented on fig. 6.2, г

The considerable plastic deformation which is taking place at extension of metal for elimination сamber Fix-A-Dent Auto Body in a cold condition, increases a behr bmw parts true surface of metal on a restored site and worsens its firmness films. As a result corrosion firmness of metal worsens. Therefore editing rough (wavy, small concave surfaces) panels of bodies and plumage carry out without and increases varis bmw parts in the area of metal by means of a basic plate 2 and a special hammer 1 (fig. 6.3), having a notch on a working part. At elimination of dents by the given way metal is not stretched, and the length of the panel 3 is restored to initial forms and the sizes.

To surface restoration Fix-A-Dent Auto Body details in readily available places apply various Fix-A-Dent Auto Body tools according to curvature of a restored profile of a detail, i.e. Taking into account radiuses, transitions of bmw suspension parts various curvature and rigidity edges. On fig. 6.4 variants of use of shaped plates, anvils, оправок and Fix-A-Dent Auto Body a hammer are shown at restoration of a surface of a forward wing of a body in section А-А.

Camber elimination on a surface of a body a method of heating and fast cooling. It is based on use of processes of expansion and усадки metal, at heating and the subsequent cooling. Whereas plasticity кузовной steels at a room temperature insufficiently high, apply its heating. At heating of a soft steel to temperature nearby 800> °С (red colour) it becomes plastic and is easily deformed. There is no necessity to heat up all surface, and it is enough to choose for this purpose some suitable points.

Fig. 6.2. Restoration of the form of details with use Fix-A-Dent Auto Body the tool: and - elimination of deformations on rectilinear sites of obverse panels; - correction of deformations on details with not round surfaces (a dotted line the initial form of an original detail is shown); in - elimination of insignificant dents on obverse panels of a body; г - elimination of dents on the obverse details having the rounded off surface (figures specify sequence of drawing of blows of a hammer)

Heating of metal of camber on a body carry out a coal electrode сварочного the device (fig. 6.5,) or a flame of a gas torch (fig. 6.5,). The source of heating Most convenient for this purpose is the oxygen-acetylene torch № 0.

At heating of a point of metal by a narrow flame of an oxygen-acetylene behr bmw parts torch the small circle of metal is quickly warmed up until red and plasticity of metal thus sharply increases. As with expansion bmw suspension parts metal interferes less нагретый surrounding metal the increase in its volume occurs at the expense of a thickening. As soon as metal will be warmed up until red, the torch is taken away, and cooling begins: нагретый the metal circle becomes dark red, black and continues to be cooled further.

At cooling metal is compressed, its volume decreases, but the length nor which width did not change is kept by the cold metal located around, neither. As metal has the temperature mismatching the maximum plasticity, that, being bmw suspension parts compressed, it absorbs a small part of lengthening of surrounding metal. Process strengthening осаживания metal make reduction of speed of distribution of heat by ring creation around нагретой parts of metal from a wet fabric, counteraction varis bmw parts of deformation by pressing metal the handle of a hammer or a pipe close нагретой points, percussion of borders of a point of metal, нагретого until red, and then and most points or Fix-A-Dent Auto Body a hammer.

Fig. 6.3. Fix-A-Dent Auto Body the small deformed sites of panels:
And - the process scheme Fix-A-Dent Auto Body: - a defective site after performance Fix-A-Dent Auto Body

Fig. 6.4. Fix-A-Dent Auto Body body surfaces in a readily available behr bmw parts place (a forward wing) with use various Fix-A-Dent Auto Body tools
Fig. 6.5. Elimination of cambers on a surface of a body a method of heating and fast cooling:
And - metal heating by a coal electrode bmw suspension parts the device: - heating of metal by a flame of a gas torch; in - sequence of cooling нагретой surfaces of a body with camber

Sharp cooling нагретого a body site carry out a tampon of an asbestine mix or a fabric moistened with water. Metal cooling leads necessary a deposit and to acceptance by a surface of a body of a demanded profile. At elimination of camber of a surface of a body by the given method it is necessary to adhere to the sequence of cooling specified in fig. 6.5, century

Elimination of camber-dent by a method of heating and metal sedimentation by shock influence. At рихтовке heating and percussion quickly bring a torch to the camber centre, warm up it and take away a torch as soon as parts foe bmw until red the stain will reach diameter bmw salvage parts no more than 10 mm at a thickness of metal of the panel of 0,6 0,8 mm. At heating it is necessary to watch, that metal has not behr bmw parts begun плавиться. If work carry out alone a torch put aside, and under sheet place a manual anvil almost under defect. Quickly tap not reddened metal around нагретой points, and then нагретую a point while metal still remains dark red. It is preferable to perform this work hammer.

At Fix-A-Dent Auto Body a hammer-gladilkoj force of blow should be small not to create a stretching of metal instead of усаживания. If camber small, enough one point. Work consider finished only when varis bmw parts metal will cool down to an ambient temperature. To cooling acceleration apply the fabric moistened in water. If it is necessary to carry out additional dot heatings it is necessary to do them no more than two, three between each cooling.

After cooling нагретого sheet spend thin Fix-A-Dent Auto Body tempo a site to level a surface of metal which had before deformation.

For elimination of extensive camber (dent) of a surface of a body metal preliminary heat up (fig. 6.6,) in a place of prospective blow. Sedimentation of extensive camber of metal carry out on a basic plate with parts foe bmw the help hammer bmw salvage parts (fig. 6.6,), and dent elimination - with use of a hammer and a shaped plate (fig. 6.6,). The sequence of preliminary heating and drawing of blows at elimination of extensive cambers (dents) depends on the camber form. If camber round points of blows 1-4 have on a spiral in a direction from periphery to the centre and if camber long and narrow points of blows 1-16 have narrow numbers (fig. 6.6,).

Elimination of dents in remote places of a body. Elimination of such dents make by means of levers, basic plates and the special adaptation of shock type.

Correction of dents on obverse surfaces in a zone of an arrangement of amplifiers make by means of the levers which choice depends on bmw replacement parts an arrangement and character of a dent. On fig. 6.7 schemes of editing and examples of correction of elements of bodies with use of levers are resulted. The dents located under amplifiers, eliminate flat levers. and rigidity edges on open sites restore by means of varis bmw parts basic plates and a special chisel. Заломы and dents of panels of doors, and also wings correct levers, using as a support internal elements of panels of a cowl, doors, a mudguard guard etc.

Elimination of deformation of the panel of a threshold (fig. 6.8) make its opening, editing, and welding. On fig. 6.8, and, receptions of opening of a threshold are shown. To opening apply a drill, a drill or an integral vertical drill, a chisel, the lever and a hammer. Editing of the deformed panel of a threshold and restoration of its form make the lever-clip and Fix-A-Dent Auto Body a hammer. the restored bmw replacement parts panel of a threshold carry out a hammer with use of a basic plate as support. In summary carry out welding of the external panel of a threshold with an overlay varis bmw parts and the floor panel

Superficial flat dents sometimes manage to be corrected, not opening the latent cavity. For this purpose in the deepest part of a parts foe bmw dent drill an aperture in diameter of 6 mm through which insert the bent end of a core and extend a concave part of the panel before its normal position. Then an aperture fill with solder or bmw suspension parts

Fig. 6.6. Elimination of extensive cambers (dents) on a surface of a body a heating method in a combination to shock influence: and - metal heating; 6 - camber sedimentation parts foe bmw on a plate; in - elimination of dents by a bmw replacement parts hammer on a shaped plate; г - sequence of heating and metal sedimentation at elimination of cambers (dents)

Elimination of deep dents spend the adaptation of shock type. The adaptation consists of a shock hammer, moving on directing core , bmw auto parts and coming to an end with the handle with a persistent platform. Working body is the complete set of the replaceable tips intended for correction of dents on panels of a body. Replaceable tips connect to an adaptation core a carving.

Quality assurance Fix-A-Dent Auto Body carry out visually or palpation parts foe bmw of a controllable surface by a hand palm. Visually convex or concave parts for bmw cars surfaces by their viewing under a corner or sideways are most easily supervised. To the control of flat surfaces apply rulers. At palpation the slightest roughness is felt as a hand palm.

BMW spare parts: BMW used parts: Repair BMW: If there were problems with coupling

The given way can save to you from 20$ to 100$, but do not forget what to go by this car then to you. BMW replacement parts, it is always better, though and is much more expensive.

Attention! Before something to remove or change I recommend to check up simply level of a brake liquid in a tank. If necessary to add and pump over coupling there is nothing not removing.

Recently has bought BMW 730 E32 and I first with what has faced - unexpectedly for me for the second day of my driving the coupling pedal has started to come back badly, and then and has at all sunk in a floor. Thanks to it I nearly have not caught up «Ме … 600 SEL» trying to return her hand back.

After that I have decided to be engaged in repair. Has put the car in garage and has started to search for malfunction …
Has climbed under the car and has seen varis bmw parts that the working cylinder of coupling all in a brake liquid, and also all surface of a box under it. On cylinder hissing by pressing a coupling pedal it was clear, that cuffs in it has died. Has removed a cover from a bmw used parts flank of a brake liquid together with a float. Has started to remove the working cylinder of coupling - it fastens on two nuts. Bottom turns away easily, and here the top has forced will work - very difficultly подлезть. Having turned off both nuts, I remove the cylinder and I try to turn away a brake tube. After several attempts I have thrown this employment and have decided it not to turn off, it is a little of it to straighten and try to change cuffs directly there.
Having removed the cylinder, has removed from it it can appear too torn and most likely, to it you will not find replacement. It is possible to put and fragmentary (пыльник protects the cylinder from dirt and dust hit), but service life a cuff will be little bit less. Then, a companion on my command has pressed a coupling pedal, and here, the piston with a cuff at me in hands (ATTENTION! Remember as cuffs sat on the piston).
Has started to search cuffs and not having found it in one shop (everywhere suggested to buy the whole cylinder), has gone on the automobile market and has picked up the similar. It has appeared it of cuffs has approached on internal diameter, but was little bit more on external, than native. To select cuffs follows, preliminary having measured the shtangel-compasses. The analogue should have internal diameter little bit less native or same, and external it is, little bit more, on width of special councils is bmw suspension parts not present. The main bmw salvage parts thing - that it normally sat on the piston. But it is not necessary to forget, that native new parts foe bmw it will be always better than any ours.
Taking the piston, a plot of cuffs on it. ATTENTION! To put on cuffs it is necessary correctly - just as the native earlier sat. The most interesting now has begun - it is necessary to insert the piston with a cuff back into the cylinder. For this purpose it is necessary to turn off the union on the cylinder. A screw-driver taking more thin in one hand, a core in another, the beginnings it to insert. A core I press the piston pressing it in the cylinder, and with a screw-driver on the sly I fill cuffs on a circle (to fill better with a stupid subject and it is very cautious not to tear cuffs). Through some attempts of cuffs rises on the place. I put пыльник the cylinder and all the rest into place. And already I twist the cylinder, then the union.
Now it is necessary to pump over only coupling until the pedal of coupling will not start to work as it is necessary, and from the union the made foam liquid or simply air will not cease to go. Prorolling procedure is carried out also as on any our car - one swings time six-seven, to press it is necessary quickly, to return (probably at first a hand) it is necessary slowly, then holds a pedal. The second person from below turns off the union on one-two turn, lowers a liquid and again twists the union. The third person adds at this time a brake liquid in a tank (ATTENTION! Do not regret bmw replacement parts).
Probably it is necessary to resort to reception of compulsory prorolling at first:
The first person lifts a coupling pedal upwards and after the coupling pedal will appear at the top of the second the person turns off the union, and the first at the command of the second, (Protect eyes!) presses a pedal as it is possible more sharply, and keeps it in the pressed condition. After pressing, the strong stream of air with splashes bmw auto parts will be pulled out from the union then we twist the union, we lift a pedal, we add a liquid in a tank (I do not advise to add a brake liquid flowed out of the union). This reception can be repeated until in a coupling pedal not to appear elasticity.
After all done all should work normally.

There is a by-effect: during the first 10 – 100 kilometres the pedal can become again soft and fails (by sharp pressing all should work normally) a little. It though and is unpleasant, but it is not terrible - there is a grinding in a cuff.

Further all should be normal.

The given way is tested on 730 – E32 and 316 – E21.
In theories, this way should approach for any BMW.

BMW spare parts: BMW used parts: Repair BMW: All truth about shock-absorbers BMW.

Shock-absorbers on the design happen:

- The two-trumpet hydraulic

- One-trumpet gas hydraulic with high pressure gas

- Two-trumpet gas hydraulic with gas of low pressure
And - air under atmospheric pressure- gas. In - oil

Difference between 1 and 3 that at the second the space between cylinders is filled by gas under rather small pressure.

What for gas? - Basically, the design 2 has the big resistance to foaming that allows to receive stable enough characteristics in all range of temperatures and suspension bracket courses. But....

With reference to operation, namely to suspension bracket operating modes on real road, this stability is not always necessary. For comfort, controllability, Road holding is important there are transitive modes where, for example, the pure hydraulics, foaming, will bmw replacement parts provide to the shock-absorber necessary rigidity and characteristics in this mode. Therefore when there is a question: gas or hydraulics - a question is incorrect. All depends that that offers, or other firm for the concrete car, and than she explains it. And when one and firm on the same car offers shock-absorbers DIFFERENT in a design anything it not motivating - I DO NOT TRUST! And I conduct thought to one: not very well what shock-absorber on a design, is important the manufacturer, its reputation and quality of production. And these components define both the price, and durability of shock-absorbers, and sensations from driving.

For example, it seems reasonable approach KONI, shock-absorbers letting out two series: KONI Sport and KONI Special - the client should not excite, what at it a design of shock-absorbers gas/hydraulics is offered to it on a choice: for comfortable driving Special, for active Sport. And in both series there are all three constructive schemes. Though are more used on off-road cars and heavy cars.

Personal Charts of shock-absorbers for road application (for pure sports - in another way. Since here all already depends on ambitions and the prices) I Wish to notice also, that the shock-absorbers standing in a series by enough mass cars, make some other sector of the market. As a rule, shock-absorbers Bilstein in a series on BMW are purely hydraulic and have smaller ходимость, than Bilstein Sport, on it.

KONI and Bilstein

At once I will make a reservation why these firms have divided 1-2 places: at one it is better shock-absorbers on one cars, at others on others. If in conversation bmw salvage parts with representatives you mention other firm (Monroe, Boge, Kayaba) - fastidiously screw up the face (these to us not competitors), at the mention of someone from them (KONI or Bilstein), strain, speak, what yes supposedly quite good shock-absorbers, but than them will be better.

These shock-absorbers the most expensive. But also quality at height (die, as a rule, together with the car).

The approach to manufacture:

KONI - to make better than that costs by the car initially (from factory). Supplier FERRARI *, Aston Martin, Mazerati, Lamborghini, Lotus Elize, Dodge Viper, Porsche 968 (if remember such car)

Advantage - possibility of adjustment of rigidity both for deterioration indemnification, and for "прохватить" with adjustment without removal though as shows experience to regulate Special it is necessary through 30... 40 thousand in km. Are made KONI in small amounts. Culture of manufacture at height: each shock-absorber before packing in a box passes test for accurate conformity to the set characteristics (though than more cheaply the shock-absorber is more supposed by that an error in characteristics, and in Germany on them give the LIFELONG guarantee on one car at one owner.

Are issued:

KONI Special (red colour) - for comfortable driving. I.e. at installation of these shock-absorbers at the car smoothness of a course lost-free (I underline lost-free) for controllability (however, controllability it becomes frequent even better) improves

KONI Sport (yellow colour) - for aggressive, energetic driving (For the majority of cars these shock-absorbers have possibility of adjustment of effort of a release without removal from the car). Comfort on them it is essential less than on Special, but the car excellent and allows to increase speed of passage of turns essentially.

KONI Sport kit - the complete set of the truncated springs and the shock-absorbers calculated on application with short springs

KONI Load-a-Juster - the shock-absorber with the spring wound on it with the progressive characteristic that allows to avoid bmw auto parts the car at the big loading (a variant for summer residents).

Bilstein - to make in own way. I mean German Bilstein, yellow color of a series Sports, instead of the Standard dark blue, Spanish (quality it is weak) Distinctive line of these shock-absorbers, that they practically all. At Bilstein accurate orientation to the uncompromising approach - Sports mean rigidly. If on Horses Sport shakes not so, on these з (especially if a forward cartridge - double-dealing fellow McPherson) the real (own sensations from trips on Е34).

The supplier: CHEVY Corvette LT, BMW (partially, and basically hydraulics - that you you will not make for the sake of profit), Porsche Boxter, MB, Ferrari *.

Quality of assemblage too at height. "Yellow" Bilstein serves longer the car (even suffices on one race in the presence of corresponding springs)

Are issued:

Bilstein Sport - sports shock-absorbers (not for sports, and for road application)

Bilstein Sprint - too most, as Sport, but calculated on the truncated springs

Bilstein Rally - for sports application.

Suspension bracket complete sets (springs and shock-absorbers of series Sprint)

Bilstein Standard - blue colour made in Spain. Near to present Bilstein I would not put it - not Bilstein it (there is it in 1.5. 2 times are cheaper than German, quality is worse).

* Originally Ferrari left factory exclusively on shock-absorbers KONI, then, since 1996, supplier Ferrari became Bilstein (it has appeared is cheaper), and now the most part of cars descends on SACHS though adults Ferrari still go on KONI.

BOGE

The German firm making shock-absorbers on the conveyor of many German factories AUDI, VW, BMW, VOLVO, AlfaRromeo. Now belongs SACHSу. Sound shock-absorbers, no more that.

Manufacture principle: to make, let will be. They cheap, but they change characteristics of a suspension bracket of foreign cars not especially considerably, except, perhaps, "oak" series TURBOGAS

Are issued:

BOGE Pro-gas - the gas shock-absorber (with gas of low pressure), is intended for comfortable руления (for this purpose has special проточку in a zone of small courses of the shock-absorber so Monroe Sensa-Trac at all the first "the shock-absorber of new generation"

BOGE Turbo-gas - as something follows from the name aggressive, for sports driving.

BOGE Automatic - anything I can not tell, i.e. the scope of these shock-absorbers is not defined, only the general words

BOGE Nivomat - the special shock-absorber, for fans to carry помногу. In my opinion even possesses possibility to support the set road gleam without dependence from loading.

BOGE Turbo24 - one-trumpet heavy duty the shock-absorber for fans off-road and 4x4.

SACHS

Is hardly worse than BOGE, even more cheaply, are even less reliable. The approach - unification, дешивизна. On "Field" and "Classics" the same shock-absorber under the catalogue - the disorder... (For example, at KONI and Bilstein shock-absorbers different not only under numbers, but also on a design, and on rigidity, that, basically, is correct - after all one car road, and the second a jeep).

The supplier: SAAB, VW, BMW, Audi, Volvo.

Are issued:

SACHS Touring (gas of low pressure)

SACHS???? (I do not remember as the hydraulics is called)

SACHS Sporting Set - for fans of active driving, cheap enough complete set of springs with shock-absorbers.

SACHS??????? (Violet) violet colour - for sports application. KYB, Tokico

The Japanese cheap shock-absorbers. In a series on all Japanese. Rather unreliable (quality - as the random-number generator - where on 300 thousand go and repair BMW where within a month come to an end) it is especially weak the rod at hit on it of the Moscow salt porridge rusts within a week.

Gas, hydraulics and "the strengthened gas" are issued

Very much I liked their decision for Lexus - a combination of one-trumpet and two-trumpet shock-absorbers in one. The truth I do not know whose it there was an idea: Toyota or KYB.

MONROE

The approach one - aftermarket. The shock-absorber has come to an end, has gone has bought cheap but good. Reliability on the average as in advertising - 20000 km. Concerning them "the Newest working out" (see also BOGE which it is valid the first have introduced проточку in the shock-absorber) psychic-trak. If attentively to look at that place where at it проточка involuntarily you reflect: and whether it is correct is made?

It agree, on a cobble-stone, a suspension bracket course small, speeds of moving of a rod of the shock-absorber big, for the best overflowing we will make there проточку. Well, comfortably, softly. We go further. We pawn turn and, the car falls as the American 80х years. What is it? And this oil, free flowing through проточку has not provided the necessary clearing of a list. (BTW and KONI and Bilstein rest to receive the maximum gain of effort of resistance of the shock-absorber at a small gain of speed on speeds of moving of a rod to 0.33m/with, that provides to the car the best course stability and more predicted behaviour in turn (the car falls more slowly))

Are made Monroe:

Radial-matic - Pure hydraulics

Gas-Matic - Two-trumpet gas hydraulic

Van-Magnum - For off-road cars, in my opinion

Sensa-Trac - Two-trumpet gas hydraulic (basically)

I wish to note break of Monroe on the market of suppliers of original shock-absorbers: since 1996 the company delivers parts foe bmw shock-absorbers for some motor-car manufacturers: VAG, Volvo and even PORSCHE. And also their gradual steps to a market direction of "Elite shock-absorbers".

At installation of all these shock-absorbers in a suspension bracket Soviet авто, the difference is felt in comparison with the standard always. And with foreign cars in another way.

KYB, Texico, Monroe to understanding people usually do not like. BOGE and SACHAS so-so, and from KONI and Bilstein only positive emotions (except turned McPhersonов at Bilstein - but it on the fan)

My opinions, by the way, strongly coincide with opinion of Germans which are the basic consumers bmw suspension parts (70 % of sales from the general sale). But they prefer to put all this economy (as, however, and disks with rubber) on new авто to send on errands with all the heart. Therefore there almost bmw used parts nobody goes by Monroe, and basically come across KONI, Bilstein, plus of a combination from these shock-absorbers with springs Eibach, H&R, is simple suspension bracket complete sets

Naturally, there is a question on expediency of installation of those or other shock-absorbers - but it is all a question of money.

If авто - the dying foreign car which to crawl not long remains, on it KONI and Bilstein to put is obviously inexpedient, though enthusiasts come across. If the car only is bought also the person prefers not to potter with shock-absorbers further, to take pleasure in driving then obviously it is necessary to pay attention to positions 1 and 2 charts.

Principal causes of failure of shock-absorbers.

1 Incorrect installation. Pretty often. Forget to tighten a nut, put demountable cups head over heels, forget пыльники, catch at a rod пассатижами, etc.
2 Broken in a smoke or absent pylniki/chippers - rusts / the rod is lifted up and, as consequence, the epiploon comes to an end
3 Weariness of an epiploon (though heard from one mechanic - it Bilstein, brought during stagnant times has gone through 3 cars (!!!!) and till now serves.
4 Breakdown (when levers in knot)
5 Deterioration behr bmw parts systems (does not flow, on hands resistance is, and the car swings)

Still I have not mentioned such firms as DeCarbon (by the way the first "double-dealing fellow" McPherson has thought up) now on a root is bought AC Delco quality there were disgusting, characteristics too.

GABRIEL (the American cheap stuff - comes to an end for a week, road does not hold).

Crosno (the Polish went I know, but I doubt, that is healthy)

BMW spare parts: Repair of running part BMW

In the general words forward and back suspension brackets of wheels, wheels and tyres enter into concept "a running part of the car". A suspension bracket basic purpose – softening and clearing of the fluctuations transferred from roughnesses of road on a body of the car. About a running part of the BMW legends go. This knot always was famous bmw replacement parts for the quality and reliability. But nothing happens eternal. There is a deterioration of details, such as shock-absorbers, springs, spherical support, the top support to bmw auto parts bearings, draughts and stabilizer support. It is behr bmw parts promoted to no small degree also by driving on bumpy Russian roads. During movement the car starts to jump up, as if a ball, and on abrupt turn there is a characteristic loud crash.

While in service the car malfunction of a suspension bracket of the BMW can be shown differently:
On rough road at turns there is a pulling down of a forward or back axis; 
At journey of joints at asphalt or hollows extraneous knocks are distributed; 
At journey of roughnesses on road there is a body rocking; 
At braking the brake way increases;
At braking on rough road system ABS prematurely works.

If you have noticed one of signs diagnostics and the subsequent repair of suspension bracket BMW, has not varis bmw parts avoided you. Timely diagnostics and repair BMW spent in our car-care centre, will be pledge of your safety. Experts of service BMW will carry out bmw suspension parts computer diagnostics of a running part of your car, using the behr bmw parts advanced equipment and the tool, quickly and will precisely establish malfunctions of a running part and operatively them will eliminate.
Diagnostics of a running part of the BMW provides following operations:
Check of a condition of shock-absorbers, springs and basic cups; 
Absence check люфтов in spherical support and steering tips; 
Condition check, etc. knots of a running part of the BMW; 
Check of serviceability of basic bearings;
Coupling check; 
Check brake , disks, drums, hoses.
By results of diagnostics of running part foe BMW each client receives diagnostics sheet in which it is underlined on hands:
Necessary amount of works and its cost; 
The list of the works, necessary to execute first of all; 
Recommendations about application of bmw salvage parts.

Usually first of all happens it is necessary to execute following kinds of works:
Repair of shock-absorbers BMW; 
Replacement the BMW; 
Replacement and adjustment of basic bearings;
Coupling replacement.

Sometimes it happens quite enough for continuation of safe driving. Do not tighten with arrival to car-care centre BMW, after all from serviceability of all details of the car, safety of driving depends. Repair of suspension bracket BMW – not the most bmw used parts terrible, that can happen, skilled masters will quickly cope with this problem.

BMW spare parts: BMW 7 series

Cars of a representation class. Excellent dynamic qualities, stable выбег in rectilinear movement on inertia, magnificent informative and reliable brakes, amazing work parts foe bmw of a suspension1988 bmw picture 735i + used parts bracket. Even the car more varis bmw parts, promptly schoolmates looks: the low cowl topped with firm "nostrils" of a lattice of bmw 750i performance parts a radiator, the big glasses.

A series 7 - a representation class - let out since 1977 (the first family - Е23). "Seven" always built with a bmw k75s parts body a sedan. Engines - only six-cylinder (on model 745i - with a turbo-supercharging), since 1979 - with fuel behr bmw parts injection "Me-Motronik”. Cars of the parts foe bmw first generation for "aggressively pointed line at bmw 750i performance parts us have nicknamed"sharks".

The new body has appeared in 1986 (Е32). "Seven" of this family are a little similar to cars of 5th series - Е34. Except two six-cylinder bmw suspension parts engines (model 730i and 735i), since June of 1987 under a cowl of magnificent1988 bmw picture 735i + used parts model-leader the V-shaped 12-cylinder motor (BMW-750i) "has registered".

Last family BMW E38 on the conveyor since 1994. The body became more "licked", headlights according to a varis bmw parts, modern corporate style bmw suspension parts have hidden under the general glasses. Gradually there is "shake-up" of engines. Have bmw k75s parts returned behr bmw parts "weak" "six" of 2,8 l. Engine V12 volume - 5379 sm3 has 1988 bmw picture 735i + used parts increased. Since 1996 it is possible to get "seven" with a turbodiesel - 725tds.

BMW spare parts: BMW 5 series

Unique a combination of intelligence, capacity and an aesthetics воплощенны in a sedan of 5 series. A basis of 89 bmw 525i parts, parts bmw 535i creation of this car - deep understanding of concept BMW "pleasure at the wheel". And powerful engines and an varis bmw parts innovative superficial running part of a sedan open new measurement of pleasure. The1998 bmw 528i parts
advanced system of active driving and the management concept iDrive establish new standards of intellectual bmw suspension parts design. Each element BMW of 5 series is the expressed confidence in послушности the car on road.

A series 5 (Е12) has appeared in program BMW in September, 1972. Outwardly these cars resembled cars of a series 3, but differed, besides the sizes, four round headlights. Sedans varis bmw parts with four-cylinder engines - models 520 (and 520i (injection "BOSH K-dzhetronik") were first-borns. In August of 1973 was issued six-cylinder BMW-525, and in February of 1974 - BMW-528 also with carburettor Since 1977 instead of four-cylinder BMW-520i did six-cylinder updating. Transmissions on "пятерках" the first generation were four-stage.

In 1981 the body and interior furnish have changed. On this family (Е28) four-stage boxes have left in the past, gradually behr bmw parts replaced each other engines. Therefore cars 1998 bmw 528i parts
of family E28 at parts foe bmw us too name transitive. In 1983 carburettor model 518 has quitted the stage. To it 89 bmw 525i parts, parts bmw 535i on change has come 518i with injection "BOSH LT- dzhetronik ". Have the same year appeared 525е and Turbodiesel 524td. Less powerful "atmospheric" diesel engines began to establish since 1986.

In January, 1988 the firm has begun family E34 manufacture. The body became more streamline, there were vertical indexes of turn, antifog headlights under a bumper. Since 1990 on the bmw suspension 1998 bmw 528i parts
parts version 520i and 525i parts foe bmw established modernised 24-klapannye six-cylinder engines. In 1992 of model 530i and 535i have received new motors V8. In 1991 there was a versatile person and all-wheel drive BMW-525ix.

Since September of 1995 in Bavaria let behr bmw parts out family E39. Manufacture of four-cylinder variants is stopped. There were new models BMW-525tds, 528i, BMW-540i has received the new engine in working volume of 4,4 l, and the car with the 2,5-litre engine began to designate 523i.

BMW spare parts: BMW 3 series

In BMW 3 series of the theory of high technologies were embodied in practice. More thirty years ago company BMW has created the first sedan. BMW Е30 name "a legend of a German car industry", and BMW Е36 in the early nineties was parts foe bmw an automobile fashion. Today BMW 3 series continue this tradition in the best style.

A series 3 was issued in 1975, having come in the stead to family 1500/1600. A factory designation the first generation - Е21. Outwardly these cars were allocated with vertical indexes of turn and two big headlights. Е21 let out bmw z3 performance parts only with a two-door body. In scale varis bmw parts of motors there was one with system injection "BOSH K-dzhetronik" (model 320i), other engines equipped with carburettors95 bmw 325i parts Transmissions - mechanical, four-or five-step. In 1977 there was the first bmw suspension parts with six-cylinder впрысковым the engine in volume of 2 l, replaced the previous four-cylinder model. Its index, according to the rules accepted in firm, remained former - 320i.

In 1982 on the conveyor there was family E30 with a new two-door body. Its lines became smoother, and the lattice of a radiator and traditional firm "nostrils" have decreased. All Е30 were with four round headlights and the indexes of turn built in in a bumper. The old body has remained only at model 315 which have behr bmw parts soon laid off. Engines BMW-315 and 316 - carburettor transmissions - with four steps in a standard varis bmw parts complete set and five - by request. On other models95 bmw 325i parts there were motors with injection of fuel and five-step boxes in the base version. "Automatic machine" offered to order for any model, except 315.

In 1990 started family E36 which let out and till now. The first appearance was replaced by a sedan. In 1992 on the conveyor there was a new compartment, in 1993 - a cabriolet and hatchback parts foe bmw and in 1995 - the versatile person. The scale of engines has95 bmw 325i parts been expanded by a turbodiesel (BMW-318tds). Instead of a diesel engine in volume of 2443 sm3 (324td) have started to let out new - 2498 sm3 (325td and 325tds). The bmw suspension parts six-cylinder motor of model 325i has given way to more powerful in volume of 2,8 l.

Most of allmade BMW 3rd series in body Е46 with 4-cylinder engines. Such cars initially cost more cheaply, than models with the well-known 6-cylinder units. Four-cylinder motors was a little. The weakest, volume 1,6 l (102 h.p.), it is possible to see only under a cowl of 3-door hatchbacks of the first years of release (316i Compact). After 2001 there was a new bmw z3 performance parts scale of 4-cylinder engines with system Valvetronic. From this time on the version 316i Compact began to put already 1,8-litre motor (115 л.с). It is a lot of in the market and "budgetary" sedans 316i. They at first were equipped simple 8-klapannym with the motor in volume of 1,9 l capacity of 105 h.p., and then have received 1,8-litre 16-klapannye units (115 h.p.). Further goes 318i. Such cars too can have different engines. So, the models made in the late nineties were95 bmw 325i parts equipped with the 1,9-litre motor (8 valves, 118 h.p.) And the hatchback 318i Compact had thus the same unit on volume, but with 16th valves (140 h.p.). behr bmw parts Well and the last 318i are equipped by already 2,0-litre engine capacity of 143 h.p.

BMW spare parts: Repair of the engine of the BMW

Even such reliable car as BMW from time to time demands carrying out of repair work. Unfortunately, sometimes there comes the moment when falling of capacity of the engine, already it is impossible to correct the increased expense of combustive-lubricating materials, deterioration of starting properties of the engine behr bmw parts and faults in all operating conditions bmw suspension parts usual adjusting actions. Size of a resource of the engine define in the speed of deterioration of the details, arising under the influence of loadings. As a rule, the accelerated deterioration varis bmw parts of the engine occurs at non-observance of service regulations and car maintenance service. As a result we receive repair of the engine of the BMW. And it is good still if it is a local problem and we should not carry out engine BMW major repairs, that in all cases means considerable financial expenses.

Considering, that motor potential of the Bavarian engines is very great, at correct operation repair of the engine of the BMW can come very much not soon. The resource of engines with the turbine of low pressure is comparable to a resource the engine, and here at parts foe bmw engines after parts foe bmw they will run two hundred fifty thousand kilometres, there can be problems. Especially provided that such car has got to the person preferring driving on raised turns.

If at your iron horse забарахлило heart engine BMW diagnostics is as soon as possible necessary. It is caused by that at operative statement of the diagnosis behr bmw parts the probability to manage smaller blood is great and to carry current or average out repairs of the engine of the BMW instead of the capital.

That the BMW engine served you as it is possible longer, it is necessary to observe some rules. First, in time to change oil and the oil filter. It will allow to deduce that abrasive material which is formed of products of deterioration of the engine from the engine. It is necessary to use the recommended oils and not to fill in at all what concern lower class API. To avoid the bmw suspension parts raised deterioration of piston rings and cylinders, it is necessary to watch a condition of fuel and air filters through which abrasive materials get to system. The replacement of belt GPM spent in time on BMW will varis bmw parts relieve you of repair of the engine which by all means is required if the belt tears. In time spent diagnostics of the engine of the BMW allows to reveal and take parts foe bmw all measures which will rescue your purse from the big expenses. And fans of driving on high turns would like to remind, that you reduce bmw suspension parts a resource of the engine a minimum for twenty percent.

If you nevertheless had a necessity under repair or diagnostics of the engine of the BMW, in replacement of belt GRM, and also parts foe bmw under repair the compressor, address in car-care centre BMW. Highly skilled experts will spend all necessary works to the shortest terms.

BMW spare parts: Memory system in the car and a key

The memory system in the car gives the chance to the driver to create an individual set of installations for the bmw parts car. For example, to program automatic bmw performance parts inclusion of a passing light at engine start. If you want, that headlights worked after you have closed the car (function “Follow me home”), is enough to include flashing fire before an exit from your salon BMW – illumination will last even 40 seconds. The memory system bmw performance parts in a key automatically fixes the chosen installations on a personal key of the driver. Next time, when you will open the central lock, they will be activated by a remote control. The armchair of the driver will accept habitual position (function is accessible only in a combination to memory of a seat). Similarly you can adjust an automatic central air of air and air system. The memory system in a key is provided by two keys and can serve to 4 drivers, keeping individual sets of installations. The key itself "learns" the owner.

BMW spare parts: System of electronic control throttle

The system of electronic control throttle replaces the mechanical cable connecting a pedal of gas with throttle. To the Control system bmw parts of the engine the electrosignal registering each movement of an accelerator goes. On full opening throttle it is required nearby 120ms. Approximately bmw auto parts as much time leaves at the skilled driver on pressing of a pedal of an accelerator. As a result the driver has an opportunity more precisely to use capacity of the engine, enjoying smooth, free driving from vibrations even on low speeds. Thanks to the improved ignition, work of valves, an ideal arrangement throttle and to volume of injected fuel the expense of fuel and emission level is considerably optimised. Besides, the system of electronic control throttle raises safety of driving, bmw performance parts automatically reacting on dangerous mechanical malfunctions, for example, in a situation when throttle заслонки are due to negligence put in bmw parts position of full loading. To adjust engine work, having chosen between a normal and sports mode of system of electronic bmw performance parts control throttle, enough one pressing of the button bmw auto parts

BMW spare parts: System of electronic blocking of differential EDL

The system of electronic blocking bmw used parts of differential EDL with the maximum accuracy transfers brake effort to a bmw car parts driving wheel, reducing bmw parts speed to certain level. After that bmw body parts the twisting moment is transferred by means of the additional hydropump bmw motor parts to other wheels. If value of the twisting moment exceeds bmw performance parts the established norm, brake pressure is redistributed by means of the magnetic valve on a wheel which turns bmw auto parts faster others.

BMW spare parts: motorcycle BMW R1200R

Fast, prompt and maneuverable motorcycle BMW R1200R will present bright sensations from driving. BMW R1200R belongs to the class of motorcycles «with the bared torso», it is created for reception of pleasure of driving, but that to me less it is absolutely universal. BMW R1200R became much more sports, in comparison with the predecessor (BMW R1150R) is the most powerful motorcycle-roadster for today.

Engine BMW R1200R develops capacity of 109 h.p. the Maximum twisting moment reaches 115 Nanometers at 6 000 mines-1, providing solid draught bmw performance parts. The motorcycle began to weigh 198 kg, that essentially it is easier than the predecessor and positively influences both dynamics bmw oem parts, and on controllability.

BMW R1200R involves motorcyclists who like the "classical" motorcycles which design is designed for maintenance of mobile, dynamical and maneuverable driving. Unlike the competitors, new "classics" from BMW abounds with the newest technologies.


Motorcycle BMW R1200R. The successor of great traditions.

Uniqueness of engine BMW R1200R which consists in its design and technical characteristics, in a combination with tested, it is good itself the recommended suspension bracket Evo Paralever and Telelever, allow to feel faultless controllability and road keeping even on the most almost impassable sites. Besides, a full range of modern and innovative systems bmw motorcycle used partsof safety bmw performance parts, such as ABS, ASC, the pressure monitoring system in tyres and ESA (system of electronic adjustment of a running part) are accessible on BMW R1200R.

The motorcycle can be equipped by a wide range of accessories such as: a wind guard of two sizes, a luggage carrier, a high or low seat. At the disposal of the owner there will be the classical motorcycle BMW, ready to any call, including the present travel.

Prominent features BMW R1200R:

BMW R1200R:

Phenomenal universality
The power unit with system of air cooling in volume of 1.170 cubic centimetres and балансирным shaft
Capacity of the engine of 109 h.p.
The maximum twisting moment bmw motorcycle used parts reaches 115 Nanometers at 6 000 mines-1
BMS-K Electronic system of work of the engine with double injection
Easy and during too time a strong two-piece steel frame
System Telelever for more exact work of a suspension bmw oem parts bracket of a forward wheel
Excellent controllability
Pendular design of back suspension bracket Paralever with optimised on weight карданным a drive
The primary weight makes 198 kg, with a full tank - 223 kg.
Effective brake system
New integrated system ABS and ASC (antiblocking system)
Dynamical, modern design «out of time»
Wide choice of accessories.
On January, 26th, 2006 motorcycle BMW R1200R has been awarded by one of the most prestigious automobile awards of Russia – «the Gold Horn», becoming, thus, the best motorcycle according to automobile experts.

BMW spare parts: Wiring diagramme: BMW KSD

Program BMW KSD contains the catalogue bmw used parts of norms-hours and expert estimations for firm BMW cars, the information bmw car parts is presented since 60th years. Program BMW KSD works from CD, installation does bmw body parts not demand bmw parts online, is completely translated into UA, including Help. Wiring diagramme
the interface of program BMW KSD as much as bmw motor parts possible simple and convenient, bmw used parts except Russian, supports some more European languages. Wiring diagramme
Program BMW KSD is simply irreplaceable for the car-care centres specialising on car repairs BMW as allows not to think out the price bmw motor parts from a ceiling, and to make for the client full accounting of works and their cost, on the basis of official data of the manufacturer.